How To Fix A Leaky Moen Two Handle Bathroom Faucet

The first step is to turn off the water to the faucet. The next step is to remove the handles. After the handles are removed, you will be able to see the screws that hold the faucet to the sink.

Remove the screws and lift the faucet off of the sink. There will be a rubber gasket underneath the faucet. Remove the old gasket and replace it with a new one.

Put the faucet back on the sink and screw it in place. Put the handles back on the faucet and turn the water back on.

  • To fix a leaky moen two handle bathroom faucet, you will need to first identify the source of the leak
  • Once you have identified the source of the leak, you will need to turn off the water supply to the faucet
  • Next, you will need to remove the handles of the faucet
  • Once the handles are removed, you will be able to access the inner workings of the faucet
  • You will need to replace the O-rings or other parts that are causing the leak
  • Once the replacement parts are in place, you will need to reassemble the faucet and turn on the water supply
How to fix a leaky moen two handle bathroom faucet

Credit: plumbingsniper.com

Table of Contents

How do you fix a leaking bathroom faucet with two handles?

If your bathroom faucet is leaking, there are a few things you can do to try and fix it yourself. If your faucet has two handles, it is most likely a compression faucet. This type of faucet has a separate valve for hot and cold water, and each valve has a rubber washer.

These washers can wear out over time and cause your faucet to leak. To fix a leaking compression faucet, you will need to turn off the water to the faucet. This is usually done by shutting off the valves under the sink.

Once the water is off, you can remove the handles of the faucet to access the valves. Be sure to put a towel down first, as there may be some water left in the lines. Use a wrench to unscrew the packing nut from the valve stem.

This nut holds the washer in place. Once the nut is removed, you can pull out the valve stem and replace the washer. Be sure to get the right size washer for your faucet.

You can then put the valve stem back in place and screw on the packing nut. Turn the water back on and test your faucet. If it is still leaking, you may need to replace the valve stem.

If your faucet has a ceramic disc, you will need to replace the entire valve.

How do you replace a Moen 2 handle bathroom faucet cartridge?

Assuming you have a Moen 1225 cartridge, which is the most common type: 1. Begin by shutting off the water supply to the faucet. You’ll find the shut-off valves under the sink.

2. Use a Phillips screwdriver to remove the screw that secures the handle to the faucet. 3. Remove the handle and set it aside. 4. Use a wrench to remove the retaining nut that holds the cartridge in place.

5. Pull the cartridge out of the faucet. 6. Inspect the O-rings and replace them if they are damaged. 7. Insert the new cartridge into the faucet and hand-tighten the retaining nut.

8. Reattach the handle and turn on the water supply.

What causes a Moen bathroom faucet to drip?

A dripping Moen bathroom faucet is often caused by a worn-out washer. The washer is a small, disk-shaped piece of rubber that is located under the handle. Over time, the washer can become dried out, cracked, or otherwise damaged, which can cause it to leak.

In some cases, the washer can simply be tightened to stop the leak. However, if the washer is damaged, it will need to be replaced.

How do you fix a leaky Moen faucet handle?

Assuming you have a Moen faucet that leaks at the handle, there are a few things you can do to fix it. You may need to replace the O-rings, which are the small rubber washers that create a seal between the handle and the stem. You can also try tightening the screws that hold the handle in place.

If your faucet has a set screw, you may need to use a hex key to tighten it. If your Moen faucet is still leaking after you’ve tried these things, you may need to replace the entire handle. To do this, you’ll need to remove the set screw (if there is one), and then pull the handle off the stem.

You can then install the new handle by following the reverse of these instructions.

Fixing a Leaking Moen Bathroom Faucet

Older moen bathroom faucet repair

If your Moen bathroom faucet is starting to show its age, you may be wondering how to go about repairing it. After all, you don’t want to have to replace the entire fixture if you don’t have to. Fortunately, Moen offers a wide variety of replacement parts that can help you get your old faucet working like new again.

In most cases, you should be able to replace the worn-out parts with new ones without too much difficulty. Here’s a quick overview of what you’ll need to do to repair your Moen bathroom faucet: 1. Start by shutting off the water supply to your bathroom.

This will prevent any water from flowing through the faucet while you’re working on it. 2. Use a wrench to remove the handle from the faucet. In some cases, you may need to use a screwdriver to remove a set screw that holds the handle in place.

3. Once the handle is removed, you should be able to see the valve stem. Use a wrench to remove the packing nut that secures the valve stem in place. 4. Pull the valve stem out of the faucet body.

You may need to use a pair of pliers to grip the stem and pull it out. 5. Inspect the valve stem for any damage. If it looks worn out, you’ll need to replace it.

Conclusion

Leaky faucets are a pain, and they can be expensive to fix if you have to call a plumber. But if you have a Moen two-handle bathroom faucet, you’re in luck. Moen faucets are easy to repair, and you can do it yourself with just a few tools.

First, identify the source of the leak. If the leak is coming from the handle, you’ll need to replace the O-ring. If the leak is coming from the spout, you’ll need to replace the washer.

Once you’ve identified the source of the leak, turn off the water to the faucet and disassemble the faucet. Replacing the O-ring is a simple matter of unscrewing the handle and popping in a new O-ring. Replacing the washer is a little more involved, but still easy to do.

You’ll need to remove the spout and then unscrew the retaining nut that holds the washer in place. Pop in a new washer and screw the nut back on, then reassemble the faucet. Once you’ve replaced the O-ring or washer, turn the water back on and check for leaks.

If the leak is gone, you’re all set! If not, you may need to replace the other washer or O-ring.

About Author:

Danyal is a Freelance Copywriter that has been writing for online publications including Home improvement, newsworthy blogs and even a few personal blogs. He has a passion for writing and loves to share his knowledge with everyone who wants quality information.

Leave a Comment